Van Upfitting & Fleet Fabrication South FL

Service Overview

Van Upfitting Fabricated to Your Workflow

Your van is a mobile workspace. We engineer custom steel and aluminum interior systems that turn cargo space into organized, efficient tool storage, built exactly for how you work.

Fine Edge Industries designs and fabricates custom van upfitting systems for electricians, plumbers, HVAC technicians, general contractors, and specialty trades throughout South Florida. Every system is measured to your specific van model and configured around your actual equipment and daily workflow.

We work in steel and aluminum, weld everything in our Hallandale Beach shop, and deliver finished systems ready for bolt-in installation, or install them ourselves. Single vans or entire fleets, we have the capacity and pricing structure to support both.

What We Build

Van Upfitting Systems We Fabricate

Custom Shelving Systems

Adjustable and fixed-height shelf units fabricated to fit your van's interior width and ceiling height. Steel or aluminum with anti-slip tread surfaces. Bin rails, drawer slides, and dividers integrated to your spec.

Equipment Platforms & Mounts

Custom-welded platforms, equipment slides, generator mounts, compressor brackets, and tool-specific fixtures that keep heavy equipment secured and accessible on job sites throughout your service area.

Bulkheads & Cab Partitions

Steel and aluminum bulkheads separating the cargo area from the cab for driver safety and load containment. Solid panel or window insert configurations, with integrated pass-through options where needed.

Cable & Power Management Frames

Welded wire management frames, conduit brackets, and power distribution mounting panels for electrical service vans, low-voltage contractors, and telecommunications fleets. Keeps cable runs organized and accessible.

Our Process

How We Upfit Your Van

Four steps from your empty cargo area to a fully operational mobile workspace, with no guesswork and no stock compromises.

01

Site Survey Your Van

We measure your specific van model's interior, including floor width, ceiling height, wheel well locations, door openings, and existing anchor points. We also document what equipment, tools, and materials need to be organized.

02

Design Around Your Workflow

We lay out your shelving, platform, and storage system based on how you actually work: most-used tools accessible first, heavy equipment low, dedicated zones for materials and supplies. You review and approve before we cut anything.

03

Fabricate in Hallandale Beach

Your system is cut, welded, ground smooth, and finished in our Hallandale Beach shop. Steel systems receive primer and powder coat. Aluminum systems are brushed or anodized. Lead times typically run 5–10 business days for single vans.

04

Install On-Site or In-Shop

We install at your facility, job site, or at our Hallandale Beach shop. All systems bolt directly to factory anchor points and van floor channels. No welding to the van itself. Removable and transferable to a replacement vehicle.

Material Options

Steel vs. Aluminum: Which is Right for You?

Both materials produce excellent van upfitting systems. The right choice depends on your load requirements, weight sensitivity, and budget. We can also combine both in a single system, steel where strength matters, aluminum where weight savings count.

Steel

Maximum rigidity, handles heavy equipment and tool loads without flex
Fully weldable, complex custom shapes and integrated brackets with no fastener hardware
Powder coat finish in any color, matches fleet livery or company branding
Cost-effective for single-van and small fleet builds
Best for: Plumbers, HVAC, contractors carrying heavy pipe, fittings, and power tools

Aluminum

Lightweight, reduces cargo load, improves fuel economy across a fleet
Naturally corrosion-resistant, no rust in coastal and humid South Florida conditions
Clean appearance, brushed, anodized, or clear-coat finish for a professional look
Fleet-preferred material for high-mileage service vehicles
Best for: Electricians, low-voltage contractors, service techs, cable and telecom fleets

Project Gallery

Van Upfitting from Our Shop

Custom steel and aluminum van interior systems fabricated at our Hallandale Beach facility for South Florida contractor and service fleets.

Service van exterior ready for upfitting, Fine Edge Industries South Florida

Service van exterior, pre-build staging at our Hallandale Beach facility

Custom steel shelving system being fabricated and fitted, van upfitting in progress, Fine Edge Industries

Custom shelving system in progress, fabricated and fitted to spec at our Hallandale Beach shop

Finished van interior, rear view of completed custom steel shelving system, Fine Edge Industries

Finished build, rear-centered view of completed custom shelving and equipment layout

Full interior view, completed van upfitting system ready for fleet deployment, South Florida

Full interior, custom steel system ready for equipment loading and fleet deployment

Custom van shelving system for South Florida contractor fleet

Who We Upfit

Built for South Florida's Trade Professionals

Electrical contractors & low-voltage technicians
Plumbing & mechanical service companies
HVAC service and installation fleets
General contractors and field crews
Telecommunications and cable fleets
Fire protection and sprinkler contractors
Security and alarm service vehicles
Specialty trades requiring custom tool organization

Talk to Us About Your Van →

Service Area

Van Upfitting for South Florida Contractors

Fine Edge Industries is located at 2043 John P Lyons Ln, Building C, Hallandale Beach, FL 33009, centrally positioned between Miami and Fort Lauderdale with easy access from I-95 and the Florida Turnpike.

We serve contractor and fleet upfitting clients in Miami, Fort Lauderdale, Hollywood, Miramar, Doral, Hialeah, Davie, Pompano Beach, Weston, Medley, Opa-locka, Deerfield Beach, and throughout Broward County, Miami-Dade County, and Palm Beach County.

Whether you're searching for "van upfitting near me", "contractor van shelving Miami", or "fleet fabrication Fort Lauderdale", Fine Edge Industries builds your system from scratch in our own shop, to your exact van dimensions and workflow requirements.

Request a Van Upfitting Quote Industrial Fabrication → Structural Steel →

Client Reviews

Trusted Across South Florida

★★★★★ 5.0 Google (5) ★★★★★ 4.9 Angi (7)

★★★★★

“The best place to materialize your imagination. They put a lot of effort into understanding and building your project. The punctuality was the most impressive part.”

Victor A. via Angi

★★★★★

“They resolved projects and issues for me in a very short time, problems that others had been unable to fix in the past. Extremely satisfied, and I highly recommend them.”

Emmanuel Juste via Google

★★★★★

“Excellent and exceptional metal fabrication work. They fully understand customer needs and are highly professional.”

Alan Jean-Baptiste via Google

Read All Reviews →

Commercial Van
& Fleet Upfitting

Van Upfitting Fabricated to Your Workflow